Navigation » Dorkiphus.net
»
1/2" drive 10mm allen socket
| Tools Needed/For Loan If you need to borrow some tools, or have tools to loan, post here. |
 |
|
|
Thread Tools | Display Modes |
|
#1
08-29-2005, 04:08 PM
|
||||
|
||||
1/2" drive 10mm allen socket
Looking to borrow a 1/2" drive 10mm allen socket to remove the allen bolts that secure the front shocks to the wheel carrier.
Also may need a 150lb+ torque wrench. I think mine only goes up to 150lbs. 
|
|
#2
08-29-2005, 04:13 PM
|
|||
|
|||
|
I have the 1/2 inch allen socket (in Fairfax). I don't know how high my torque wrench goes. How far above 150lb does it need to go (so I can check tonight)
Firoze
__________________
04 GT3 Last edited by nova996; 08-29-2005 at 04:15 PM. Reason: Can't spell
|
|
#3
08-29-2005, 04:14 PM
|
||||
|
||||
|
I have a 3/8" Drive, but you could possibly use an adapter.
How tight? Another option would be to put a piece of a 10mm allen in a 10mm impact socket. I made a long 10mm (I think) for the barrell nut on the starter. The weld broke last week so the 2 piece are apart again. Remind me when I call you later. If I can dig it up, I'll bring it by.
__________________
Thanks! WCM (Bill) '81 911 SC Red Targa 3.6 '97 328is White Coupe (2nd Owners!) '08 335i Blue Sedan '05 Chevy Tahoe green '98 Jeep Cherokee XJ "Blue" '01 Toyota 4 Runner "Pearl" Darnestown, Maryland
|
|
#4
08-29-2005, 04:34 PM
|
||||
|
||||
|
Quote:
I have a 3/8th. assumption is that it will not do the job. The write up specifically calls for a 1/2" and a 150lb torque wrench.
|
|
#5
08-29-2005, 04:36 PM
|
||||
|
||||
|
Quote:
If you have a 10mm 1/2 inch, hope you don't mind parting with it for a couple of days. I'm in Falls Church, and can pick it up any time it's convenient...
|
|
#6
08-29-2005, 04:37 PM
|
||||
|
||||
|
I have all of the above and 250# T wrench. 571 233 3421.
__________________
http://vimeo.com/29896988 “Those that can make you believe in absurdities can make you commit atrocities.” Voltaire. "There is grandeur in this view of life...." Darwin. The mountains are calling and I must go. “The earth has music for those who listen” Shakespeare. You Matter. (Until you multiply yourself times the speed of light squared. Then you Energy) “We’ve got lots of theories, we just don’t have the evidence’.
|
|
#7
08-29-2005, 04:51 PM
|
|||
|
|||
|
Quote:
Firoze
__________________
04 GT3
|
Again, thank you all for the offers!
|
#9
10-07-2005, 11:19 AM
|
||||
|
||||
|
speaking of tq wrenches.... i have one that goes to 250 and love it and would like to continue my "collection" starting w/ the small one for the smaller jobs.
the one i am considering starts at 20# and goes to 100, is that "not low enough" for some jobs? (i believe valve covers are in the 'teens right? rotor-to-hub is somewhere near 18# i think, but would it kill it if it was torqued to 20?) just thinknig out loud, thanks.
__________________
no.don't.stop. --if you just want sperm to come out... one two thweeee! one more cr sp nasa t-3 i used to drove, you've probably never heard of me
|
|
#10
10-07-2005, 02:40 PM
|
||||
|
||||
|
I think valve covers are less than 10 something like 7-8.
Dumb question, but what is the conversion from inch lbs. to foot lbs. Can't be that obvious. I think mine goes from 10 - 100 and I bought a chepo at Harbor freight which is inch lbs.
__________________
Thanks! WCM (Bill) '81 911 SC Red Targa 3.6 '97 328is White Coupe (2nd Owners!) '08 335i Blue Sedan '05 Chevy Tahoe green '98 Jeep Cherokee XJ "Blue" '01 Toyota 4 Runner "Pearl" Darnestown, Maryland
|
|
«
Previous Thread
|
Next Thread
»
Linear Mode
|
|
